Search results for: XS728T

XS728T / XS748T Firmware Version 6.5.1.74 - NETGEAR Support

Enhancements: The addition of two new modes in the UI to improve 10G link compatibility: Auto Power Down: This option fixes the issue where there is no link established on a port. Short Cable: This option fixes the issue where a 10G link speed drops to 1G. To select the new modes in the UI, click System > Management > Green Ethernet. Known Issues: The Registration page displays again after you restart the switch, even if you turned off the registration option. Workaround: Close the registration ...

XS728T / XS748T Firmware Version 6.5.1.31 - NETGEAR Support

Bug Fixes: Some copper ports (13 to 44) may not link up after a power cycle if fiber ports (port 45, 46, 47, and 48) are connected to a device whose speed is fixed at 10G. Known Issues: Registration page displays again after reboot even it was turned off before. . [Workaround]: Just close the registration window; or register the device. GUI freezes when HTTPS session times out while using IE11.0 [Workaround]: use other browsers, or refresh the whole page after timeout. If the connecting partner ...

XS728T Firmware Version 6.5.0.25 - NETGEAR Support

XS728T is NETGEAR’s new 10 Gigabit smart switch. It supports 24 10G copper ports and 4 dedicated 10G fiber ports. This release notes contains known issues and limitations for this production firmware. XS728T supports the latest Smart Control Center, please use SCC version 1.1.3.3 for switch discovery, basic configuration and FW upgrades. New Features and Enhancements: This firmware supports new and current version of IC (PHY) used by XS728T. Known Issues: ‘Destination MAC’ and ‘Destination MAC M...

XS728T / XS748T Firmware Version 6.5.1.42 - NETGEAR Support

New Features and Enhancements: To comply with California state law, the switch now requires that you change the default admin password after using the password to access the local browser UI. Added a new option under Security > Management Security > SCC Control to disable or enable Smart Control Center (SCC). It is set to Disable by default. (Note: The SCC Utility can still discover the switch even if the SCC option is disabled. If you cannot see this new option, refresh your browser or clear it...

XS728T / XS748T Firmware Version 6.5.1.26 - NETGEAR Support

Modification: This firmware 6.5.1.26 supports both XS728T and XS748T models. Comparing to 6.5.0.x release, below are new features or enhancements: Microsoft Edge browser for Windows10 Address type of IPv6 and DNS are supported for both SNTP server and Syslog server QoS policy can optionally be bound with an ACL based class to save hardware ACL resource. Max LAG number is increased from 8 to 12. Known Issues: Registration page displays again after reboot even it was turned off before. . [Workarou...

XS728T / XS748T Firmware Version 6.5.1.71 - NETGEAR Support

Enhancements: Adds the “10G Auto” option under Port Configuration on the Switching page so that you can set the speed to 10G Auto. Renames the “MAC Based” option to “MAC Auth Bypass” option under Port Control on the Security > Port Authentication > Advanced > Port Authentication page. Bug Fixes: Fixes the issue where SNMPv1/v2 traps are not transmitted when a device’s port is connected or disconnected. Known Issues: The Registration page displays again after you restart the switch, even if you t...

XS728T / XS748T Firmware Version 6.5.1.30 - NETGEAR Support

Bug Fixes: XS728T/XS748T sometimes cannot read USB Flash Drive. Cannot set multiple Member Classes to a single policy in DiffServ configuration. Known Issues: Registration page displays again after reboot even it was turned off before. . [Workaround]: Just close the registration window; or register the device. GUI freezes when HTTPS session times out while using IE11.0 [Workaround]: use other browsers, or refresh the whole page after timeout. If the connecting partner device is 1000M, port speed...

XS728T / XS748T Firmware Version 6.5.1.65 - NETGEAR Support

Bug Fixes: Fixes the issue where only 1 or 2 entries remain on the SNMPv1/v2 community table on the System>SNMP>SNMPv1/v2>Community Configuration page after a system reboot. Fixes the issue that the SNMP trap server address set through the device UI is not saved in the configuration file after a system reboot. Known Issues: The Registration page displays again after a reboot even if it was turned off before. Workaround: Close the registration window or register the device. If the connecting part...

XS728T / XS748T Firmware Version 6.5.1.77 - NETGEAR Support

Bug Fixes Fixes the issue where the Physical Status field in the Port Detailed Statistics page displays an incorrect format or an unknown status when the port link is up (See Monitoring > Ports > Port Detailed Statistics). Known Issues: The Registration page displays again after you restart the switch, even if you turn off the registration option. Workaround: Close the registration pop-up window, or register the switch. If a partner device functions at 1000 Mbps, and you disable the connected po...

XS728T / XS748T Firmware Version 6.5.1.51 - NETGEAR Support

Enhancements: To comply with California state law, remove ‘None’ option from authentication protocol for SNMPv3 (System > SNMP > SNMPv3 > User Configuration). Default is now ‘MD5’. Known Issues: The Registration page displays again after a reboot even if it was turned off before. Workaround: Close the registration window or register the device. The GUI freezes when the HTTPS session times out while using IE11.0. Workaround: Use another browser or refresh the whole page after timeout. If the conn...

XS728T / XS748T Firmware Version 6.5.1.66 - NETGEAR Support

Bug Fixes: Fixes the issue where the switch lets you set a new password that starts with special characters such as ‘$’ and ‘!’ but then does not let you log in with the new password afterwards. Fixes the issue where the value of the STP path cost for a LAG interface is overwritten with the default value when the link status of the LAG goes down. (You can set the STP path cost through the web-based management interface path Switching > STP > Advanced > CST Port Configuration.) Known Issues: The ...

XS728T / XS748T Firmware Version 6.5.1.59 - NETGEAR Support

Bug Fixes: There is a chance that a port may not link up with a device using an Intel I1219-LM NIC. The only way to recover is to reboot the switch. The pop-up window for changing the default password disappears after a few seconds of inactivity. Can’t change the LAG type on Switching > LAG > Basic > LAG Configuration when the link status of its member ports is Down. Unable to import private key successfully for SSL certificate under the Security > Access > HTTPS > Certificate Management page. K...

XS728T Firmware Version 6.5.0.23 (Initial Release) - NETGEAR Support

XS728T is NETGEAR’s new 10 Gigabit smart switch. It supports 24 10G copper ports and 4 dedicated 10G fiber ports. This release notes contains known issues and limitations for this production firmware. XS728T supports the latest Smart Control Center, please use SCC version 1.1.3.3 for switch discovery, basic configuration and FW upgrades. Notes and Limitations : Syslog servers can only be added with mode of IPv4 address; DNS and IPv6 mode of syslog sever are not supported Cable test is effective ...

XS728T / XS748T Firmware Version 6.5.1.36 - NETGEAR Support

Bug Fixes: Default Management VLAN 1 remains effective after changing the management VLAN ID to a number other than VLAN 1. This only occurs under these conditions: Assign a static IP address Select a management VLAN ID other than VLAN 1 Use a DHCP server to connect a port in VLAN 1 to a The RADIUS secret string and TACACS+ key string show as clear text in the configuration file. The SNMPv3 encryption key is present in plain text in the configuration file. Known Issues: Registration page display...

Getting started with the XS728T 10-Gigabit Smart Managed Switch - NETGEAR Support

The XS728T is a 28-port 10-Gigabit Ethernet Smart Managed Switch. It supports 24 copper 10GBased-T ports and four dedicated 1G/10G fiber ports. Frequently Asked Questions 1. What are the major enhancements for the XS728T compared with the XS712T? More 10G copper ports and fiber ports One USB port for firmware upgrade and configuration backup IPv6 Static Routing New GUI style that supports the most popular WEB Browsers (see Question 11 below for a complete list) 2. What cables can be used with th...

What NETGEAR modules can I use in the ProSAFE 10-Gigabit Ethernet Smart Managed Switches (Models XS708T, XS712T, XS716T, XS728T, and XS748T)? - NETGEAR Support

The following NETGEAR modules are supported: AGM731F AGM732F AGM734 The following NETGEAR SFP+ modules are supported: AXM761 AXM762 AXM763 (XS708T, XS712T, XS716T only) AXM764 The following NETGEAR SFP+ direct-attach cables are supported: AXC761 AXC763 Last Updated:07/07/2025 | Article ID: 30529 Was this article helpful? Yes No

What are the port speeds for the NETGEAR ProSAFE 10-Gigabit Ethernet Smart Managed and Web Managed (Plus) Switches? - NETGEAR Support

Models XS708Ev2, XS716E, XS708T, and XS716T: The copper ports are compatible with 100M, 1G, and 10G speeds. The SFP+ fiber ports are compatible with 1G and 10G speeds. Models XS728T and XS748T: The copper and fiber ports are compatible with 1G and 10G speeds. The SFP+ fiber ports are compatible with 1G and 10G speeds. Last Updated:07/07/2025 | Article ID: 30378 Was this article helpful? Yes No

NMS300 Software Release 1.5.0.2 - NETGEAR Support

This release notes contains features and known issues for NETGEAR ProSAFE NMS300 Network Management Software release 1.5.0.2. NMS300 issues fixed on 1.5.0.2 NSM300 failed to display syslog which are sent from WC9500. Key features available in this 1.5 release of NMS300 software are the following: Support for windows 10 and windows server 10 Support for additional switch, wireless access point & firewall devices. See table below. Enhance the topology map, the link flashes when the traffic exceeds...

NMS300 Software Release 1.5.0.11 - NETGEAR Support

This release notes contains features and known issues for NETGEAR ProSAFE NMS300 Network Management Software release 1.5.0.11. NMS300 issues fixed on 1.5.0.11 Removed the menu service start/stop in the start menu. The service start/stop menu doesn't work on windows 10. User can start/stop service via service manager which is provided by windows. On NMS300v1.4, SMTP uses computer's name to create a sender's email which is blocked by some SMTP server in some scenario. The Common STP data is not av...

UK PSTI Declaration of Conformity - NETGEAR Support

On 29th April 2024, the United Kingdom’s Product Security and Telecommunications Infrastructure (UK PSTI) Act takes effect. The UK PSTI Act requires consumer networking devices to meet increased security standards with the stated goals of reducing cyber attacks and better protecting individual privacy and security. All NETGEAR products sold in the UK comply with the applicable security requirements that the UK PSTI Act defines. To view the UK PSTI Act Declaration of Conformity for a NETGEAR prod...

Connecting XS728T and M5300-28G_case # 25861705 | NETGEAR Communities

Hello,   We have an M5300-28G and an XS728T. On the 5300, ports 25 and 26 (RJ-45) are bonded. On the 728, ports 1 and 2 are bonded as LAG1, ports 3 and...

Letter of Volatility for XS728T | NETGEAR Communities

I am looking to get a copy of the letter of volatility for the XS728T managed switch. I have found other links to it but they seem to be expired. 

Trunk between NetGear XS728T and ESXi | NETGEAR Communities

Hi everyone, I'm trying to establish a connection between a VM to a physical router.  I want to validate that I've configured everything correctly...

How to set a port to 1GB on an XS728T | NETGEAR Communities

There you go, it's all in the title. Is it possible to set the speed of a port to 1GB on an XS728T, regardless of the speed of the device connected to the...

XS728T - Total operational time | NETGEAR Communities

Is there any way of finding the total life uptime / operational time for a Netgear XS728T switch please? I've just bought one and want to check if it has...

XS728T Power Usage | NETGEAR Communities

The product information for this unit shows.Max power - 134.9WMin power - 67.8WEnergy Efficient Ethernet (EEE) IEEE802.3az - Switched off by defaultPower...

4 independent networks in one XS728T | NETGEAR Communities

Hi!I want to set up 4 independent networks on one XS728T. (In fact I have two of them. I have four separate networks and I would like to overcome longer...

Built-In Fan Information for XS728T | NETGEAR Communities

Hi  I would like to conduct a thermal simulation of an electronics rack housing serveral equipment which includes the Netgear XS728T smart switch....

XS728T fan replacement options | NETGEAR Communities

I wanted to create a post to help anyone looking for replacement (quieter!) fans for the XS728T switch. While the XS716T and XS708T are easy, with direct...

Need help with vlan setup netgear xs728T prosafe | NETGEAR Communities

Need help setting up vlans on 2 netgear switches. Here is my setup. Fortigate firewall port 24 is connected to port 27 on netgear xs728tThe interface...

Dual XS728T Setup with Proxied Gateway's | NETGEAR Communities

Good afternoon allI come to you seeking advice. ( I asked for advice recently, But i did not knowall the facts at the timeand the solution given would not...

Help with Inter-VLAN Routing on New XS728T | NETGEAR Communities

Hi allI am hoping for some adviceWe are replacing our current GS724Tv3 with XS724TWe are downsizing from 3 to 2I have been tasked with configuring the new...

XS728t statement of volatility | NETGEAR Communities

I need a statement of volatility for a Netgear Network Switch XS728T.  Can you assist me in getting on?   

Looking for LOV's for Netgear GS324T and Netgear XS728T | NETGEAR Communities

Any help that can be provided will be greatly appreciated

MSTP compatibility between XS728t and S3300 switches | NETGEAR Communities

I'm having trouble getting MSTP to work between XS728T and S3300 switches.  The MSTP works fine between the same classes of switches.    I'm...

XS728T Connection Issues at 10G | NETGEAR Communities

Hi, I have two new XS728T switches sat on a bench and am unable to get a 10G Link with a 35M cat6a cable however short cables link at 10G without any...

XS728T-100NES step file | NETGEAR Communities

Looking for step file for XS728T model, could you please provide respective model step for the same

New XS728T - need to connect to a 10GB Switch and a 1 GB | NETGEAR Communities

Our network team just received a XS728T switch. We are going to use this switch for a vSphere7 ESXi ClusterThe XS728T will need to...

XS728T Disconnect Issues | NETGEAR Communities

I have seen posts about this here from back in 2020, but never saw a solution for it in the posts so wanted to bring it back to life… I have this switch...

XS728T ProSafe switchnot detecting LAN Based Power Supply devices | NETGEAR Communities

  Recently purchased XS728T ProSafe switch for connecting PC and TDK lambda 5 No's power supply. I connected my laptop directly to it and was...

GS728TS(B) | 28-Port Gigabit Ethernet Stackable Smart Switch with 2 Copper/SFP+ and 4 Dedicated SFP+ Ports | NETGEAR Support

GS728TS(B) - 28-Port Gigabit Ethernet Stackable Smart Switch with 2 Copper/SFP+ and 4 Dedicated SFP+ Ports

S3300-28X (GS728TX) | 28-Port Gigabit Ethernet Stackable Smart Switch with 2 Copper 10G and 2 SFP+ 10G Ports | NETGEAR Support

S3300-28X (GS728TX) - 28-Port Gigabit Ethernet Stackable Smart Switch with 2 Copper 10G and 2 SFP+ 10G Ports

GS728TPS(B) | 28-Port Gigabit Ethernet PoE Stackable Smart Switch with 24 PoE Ports, 2 Copper/SFP+ and 4 Dedicated SFP+ Ports | NETGEAR Support

GS728TPS(B) - 28-Port Gigabit Ethernet PoE Stackable Smart Switch with 24 PoE Ports, 2 Copper/SFP+ and 4 Dedicated SFP+ Ports

FS728TPv2 | 28-Port 10/100 Fast Ethernet Smart Switch with 24 PoE Ports, 2 Gigabit Copper plus 2 Gigabit Copper/SFP Combo Ports | NETGEAR Support

FS728TPv2 - 28-Port 10/100 Fast Ethernet Smart Switch with 24 PoE Ports, 2 Gigabit Copper plus 2 Gigabit Copper/SFP Combo Ports

FS728TPv1 | 28-Port 10/100 Fast Ethernet Smart Switch with 24 PoE Ports, 2 Gigabit Copper plus 2 Gigabit Copper/SFP Combo Ports | NETGEAR Support

FS728TPv1 - 28-Port 10/100 Fast Ethernet Smart Switch with 24 PoE Ports, 2 Gigabit Copper plus 2 Gigabit Copper/SFP Combo Ports

S3300-28X-PoE+ (GS728TXP) | 28-Port Gigabit Ethernet Stackable Smart Switch with 24 PoE+ Ports, 2 Copper 10G and 2 SFP+ 10G Ports | NETGEAR Support

S3300-28X-PoE+ (GS728TXP) - 28-Port Gigabit Ethernet Stackable Smart Switch with 24 PoE+ Ports, 2 Copper 10G and 2 SFP+ 10G Ports

Networking solution ensures Hawk-Eye Innovations never misses the mark - NETGEAR Blog

Discover how NETGEAR networking powers Hawk-Eye’s real-time precision and reliability across global sporting events.

Manage Your Network Easier with NETGEAR Smart Switch CLI

Simplify network management with NETGEAR Smart Switch CLI. Configure, monitor, and troubleshoot your switches all from one place.

DC Montessori School Chandigarh - Case Study - NETGEAR Blog

DCM School Chandigarh has upgraded its network with NETGEAR Business, improving speed, reliability, and security for staff and students.

Cuisine Schmidt IT Solutions - Simplify Business Processes

Schmidt cuisine enables their advisors to present new kitchen designs using tablets to provide its customers an excellent buying experience.

Campus-wide large-scale connectivity for SIMATS delivers a better university experience for students and staff - NETGEAR Blog

Campus-wide large-scale connectivity for SIMATS delivers a better university experience for students and staff