Search results for: XS712T

XS712T Fimrware Version 6.1.0.33 - NETGEAR Support

Fixed Issues & Modification Unable to save or backup the system configuration sometimes after reboot Note : This issue is with 6.1.0.30 only. But, the configuration will still be lost after upgrading from 6.1.0.30 to 6.1.0.33. So, please reconfigure the switch after booting with 6.1.0.33 SNMP TRAP always shows its agent IP as 192.168.0.239 After an IGMP VLAN entry is deleted, related configuration is not removed completely Limitations Packet counter of 10G port does get incremented if packets wi...

XS712T Firmware Version 6.1.0.34 - NETGEAR Support

Fixed Issues and Modification ,Fixed the issue where device view does not work after updating to Java JRE 7u51 (1.7.0_51-b13) or newer versions on the host computer. ,Fixed the issue when fan #2 is stopped, instead of turning on the FAN failure LED, power LED changes from green to yellow ,Fixed the issue where unrealistic high temperature (255C) is displayed through debugging telnet session ,Messages of “Error 1 occurred reading fan” are observed ,Warning messages are observed when creating VLAN...

XS712T Firmware Version 6.1.0.12 - NETGEAR Support

XS712T is a brand new 10 Gigabit Ethernet "ProSAFE Smart Switch". It supports 12 100/1000/10000 Mbps RJ45 (10GBased-T) ports with two combo ports supporting 1G or 10 Gigabit SFP+ fiber. XS712T support the latest Smart Control Center, please use SCC version 1.1.3.2 for switch discovery, basic configuration and FW upgrades. Known issues None. Limitations Packets with frame size greater than 64 bytes and with Ether Type set to "None", counters get incremented on 1 Gig ports and counters do not get ...

XS712T Firmware Version 6.1.0.36 - NETGEAR Support

Fixed Issues: Multicast packet with destination MAC address of 01:80:c2:00:00:1c and Ethernet type of 0x88CC causes loop in properly converged STP topology. Debugging URL of ‘devshell’ is accessible without authentication. Continuous "NIM: out of bounds usp used U=1, S=0 P=13 - port too large" errors are logged while loading the device view on WEB GUI. Limitations Packet counter of 10G port does get incremented if packets with frame size greater than 64 bytes and Ether-Type set to “none”. This s...

XS712Tv2 Firmware Version 6.6.3.2 - NETGEAR Support

New Features and Enhancements: Initial Release Known Issues: Number of configured IPv6 routes is displayed incorrectly [Workaround]: Please count the listed static routes in the table. Combo port could failed to linkup with Intel NIC X520 and X710 after multiple unplug/re-plug. [Workaround]: Reboot the device. Notes: The released zip contains switch firmware (xs7xxt-v6.6.3.2.stk) and MIB files. Please unzip the file to extract the switch image for firmware upgrade. Switch FAN will run at maximum...

XS708T / XS712Tv2 / XS716T Firmware Version 6.6.3.3 - NETGEAR Support

Bug Fixes: Combo port fails to linkup with Intel NIC X520 and X710 after multiple unplug/re-plug on XS712Tv2 New Features and Enhancements: Added GUI option to enable/disable Admin Mode of Netgear Smart Control Center (SCC) Utility Added LAG Hash options in LAG configuration GUI page string modification. ‘File Upload’ changes into ‘File Export’. Added Flow control options with ‘Asymmetic’ and ‘Symmtetic’. Known issues: Number of configured IPv6 routes is displayed incorrectly. [Workaround]: Plea...

XS708T / XS712Tv2 / XS716T Firmware Version 7.0.0.24 - NETGEAR Support

Security Fixes: Fixes security vulnerabilities. For more information about security vulnerabilities, visit https://www.netgear.com/about/security. Bug Fixes: Fixes the issue where the switch is not able to obtain an IP address from the DHCP server when the DHCP Offer packet contains 2 gateway addresses. Known issues: The stored password format of v7.0.0.9 and v7.0.0.10 is incompatible with v7.0.0.24 if the length is greater than 15 characters. Workaround: Please change the password to the defaul...

XS708T / XS712Tv2 / XS716T Firmware Version 7.0.0.20 - NETGEAR Support

New Features and Enhancements: In addition to English, the local browser interface now supports German (Deutsch) and Japanese (日本語). Default “password” must be changed when you log into the switch for the first time. To configure SNMPv3, Authentication Protocol must be configured as MD5 or SHA. The ‘none’ option for Authentication Protocol is no longer allowed. Changed the default setting of the Smart Control Center (SCC) management from enabled to disabled. Note: SCC Utility can still discover ...

XS708T / XS712Tv2 / XS716T Firmware Version 6.6.3.5 - NETGEAR Support

Bug Fixes: When an SFP+ port is connected at 10 Gbps, it might not come up after a system reboot. Known issues: The switch incorrectly displays the number of configured IPv6 routes. [Workaround]: Please count the listed static routes in the table Download Link : http://www.downloads.netgear.com/files/GDC/XS708T/XS708T_XS712Tv2_XS716T_V6.6.3.5.zip Firmware Update Instructions (For XS708T/XS716T FW upgrades from v6.6.1.7 to v6.6.3.5): Make sure the firmware version of your XS708T/XS716T is v6.6.1....

What NETGEAR modules can I use in the ProSAFE 10-Gigabit Ethernet Smart Managed Switches (Models XS708T, XS712T, XS716T, XS728T, and XS748T)? - NETGEAR Support

The following NETGEAR modules are supported: AGM731F AGM732F AGM734 The following NETGEAR SFP+ modules are supported: AXM761 AXM762 AXM763 (XS708T, XS712T, XS716T only) AXM764 The following NETGEAR SFP+ direct-attach cables are supported: AXC761 AXC763 Last Updated:07/07/2025 | Article ID: 30529 Was this article helpful? Yes No

NMS300 Software Release 1.6.0.11 - NETGEAR Support

This release notes contains features and known issues for Netgear NMS300 Network Management Software release 1.6.0.11 Enhancement on 1.6.0.11: Add supported models: XS712Tv2 MS510TX MS510TXPP Smart M4300 (M4300-12X12F/M4300-24X) NMS300 Known issues and limitations Some older managed switches do not support all features available in NMS300. Short Message Service (SMS) functionality is only working in P.R China, all of other countries or regions don’t support it. This release doesn’t support uploa...

Which smart switches support 10G SFP+ slots and which optical modules can you install in an SFP+ slot? - NETGEAR Support

The GS728TXS, GS752TXS and XS712T smart switches support 10G small form-factor pluggable (SFP+) slots in which you can install optical modules: GS728TXS and GS752TXS. Support four SFP+ slots, two of which you can configure for either a 10G uplink or 10G stacking. XS712T. Supports two SFP+ slots that function as combo ports in which you can install10G Fiber or copper optical modules. You can use the SFP+ slots on the GS728TXS, GS752TXS, and XS712T to install either Gigabit SFP optical modules or ...

Getting started with the XS728T 10-Gigabit Smart Managed Switch - NETGEAR Support

The XS728T is a 28-port 10-Gigabit Ethernet Smart Managed Switch. It supports 24 copper 10GBased-T ports and four dedicated 1G/10G fiber ports. Frequently Asked Questions 1. What are the major enhancements for the XS728T compared with the XS712T? More 10G copper ports and fiber ports One USB port for firmware upgrade and configuration backup IPv6 Static Routing New GUI style that supports the most popular WEB Browsers (see Question 11 below for a complete list) 2. What cables can be used with th...

NMS300 Software Release 1.1.0.13 - NETGEAR Support

Release date: June 14th 2013 This release notes contains features and known issues for NETGEAR ProSAFE NMS 300 Network Management Software release 1.1.0.13. Key features available in this software are the following: Support for NETGEAR Managed and Smart switches Support for discovery and node status monitoring of third-party devices NOTE: Support for NETGEAR Wireless, Security & Storage devices will be available in a future release of NMS300. Following NETGEAR Managed Switches are currently supp...

NMS300 Software Release 1.2.0.16 - NETGEAR Support

Release date: September 16th 2013 This release notes contains features and known issues for NETGEAR ProSAFE NMS 300 Network Management Software release 1.2.0.16. Key features available in this software are the following: Support for NETGEAR ProSAFE Wireless products (see models number in below list). Support for NETGEAR ProSAFE Firewall FVS318G. NOTE: Support for NETGEAR Storage & remaining Security devices will be available in a future release of NMS300. Following NETGEAR ProSAFE Wireless produ...

Security Advisory for Authentication Bypass and Remote Command Execution on Some Smart and Managed Switches, PSV-2017-0857 - NETGEAR Support

NETGEAR is aware of a security issue that can allow an attacker to access the debugging URL of some models of Smart and Managed Switches without first authenticating. After accessing the debugging URL, the attacker can then execute commands on the switch, such as resetting or restarting the switch. This attack can only be executed remotely if the switch itself can be accessed remotely; for most users, a firewall will block access from outside the local network. This vulnerability affects the fol...

XS708T / XS716T Firmware Version 6.6.1.7 - NETGEAR Support

Bug Fixes: Multicast packet with destination MAC address of 01:80:c2:00:00:1c and Ethernet type of 0x88CC causes loop in properly converged STP topology. Debugging URL of ‘devshell’ is accessible without authentication. Time Zone displayed incorrectly in system information page. Combo ports 15T and 16T cannot link up with Intel NIC X552/X557-AT 10GBASE-T. Known issues: Number of configured IPv6 routes is displayed incorrectly. [Workaround]: Please count the listed static routes in the table Note...

XS708T / XS716T Firmware Version 6.6.0.11 - NETGEAR Support

New Features and Enhancements: Initial Release. The XS708T/XS716T is an 8/16 ports 10G Ethernet ProSAFE® Smart Managed Switch. It supports 8/16 copper 10GBASE-T ports with two combo ports supporting 1G or 10-Gigabit SFP+ fiber ports. XS708T/XS716T support the latest Smart Control Center, please use SCC version 1.1.3.4 for switch discovery, basic configuration and FW upgrades. Using the Download Link below, download and extract the new firmware to a convenient place such as your desktop. Download...

What are the port speeds for the NETGEAR ProSAFE 10-Gigabit Ethernet Smart Managed and Web Managed (Plus) Switches? - NETGEAR Support

Models XS708Ev2, XS716E, XS708T, and XS716T: The copper ports are compatible with 100M, 1G, and 10G speeds. The SFP+ fiber ports are compatible with 1G and 10G speeds. Models XS728T and XS748T: The copper and fiber ports are compatible with 1G and 10G speeds. The SFP+ fiber ports are compatible with 1G and 10G speeds. Last Updated:07/07/2025 | Article ID: 30378 Was this article helpful? Yes No

NMS300 Software Release 1.5.0.14 - NETGEAR Support

This release notes contains features and known issues for NETGEAR ProSAFE NMS300 Network Management Software release 1.5.0.14. NMS300 issues fixed on 1.5.0.14 Netgear Management System NMS300, version 1.5.0.11 and earlier, is vulnerable to arbitrary file upload, which may be leveraged by unauthenticated users to execute arbitrary code with SYSTEM privileges. . Enhancements since release 1.5.0.14: Support for additional switch. See table below. Model Name FW Version XS708T v6.6.0.11 XS716T v6.6.0...

Stacking Prosafe XS712T - Is it possible? | NETGEAR Communities

Can you stack the XS712T smartswitch? Thanks!

Upgrading the firmware for Prosafe XS712T | NETGEAR Communities

I am using SmartControlCenter to upgrade the firmare for subject switch. Which archive does one use to do so? There are 3 possible files: the downloaded zip,...

Help GS752TPS with XS712T and FVS336G v2 | NETGEAR Communities

Hi EveryoneQuestion for expanding my network. I currently have a FVS336G v2 running into a 24TPS. I've upgraded to the GS752TPS. I'm also considering adding...

XS712Tv2 factory resets itself | NETGEAR Communities

Bought a used XS712Tv2 on eBay back in July. I had a lot of trouble with setting it up initially. Once I got it working I upgraded the firmware to latest and...

XS716T to XS712T with SFP+ and fibre | NETGEAR Communities

Hi,I need to plug XS716T and XS712T with SFP+ and fibre. I bought 2 x SFP+10G and fibre câbles. But it does not work (no lights speed). Do I...

XS712t (v1) support of IEEE 1905.1 | NETGEAR Communities

I'm currently looking at the latest generation mesh wifi systems, but would prefer a wired backhaul. On sites for the TP-LINK BE85, for instance, people...

SFP Modules for xs712t 708t | NETGEAR Communities

which brands or model numbers compatible sfp module brands on xs 712t, 708t, 728t ,716t module port ?

XS712T IPv6 Enabled? | NETGEAR Communities

Hello, I thought the major difference between v1 and v2 was IPv6 support.    My v1 seems to support it.   Please advise. 

XS712Tv2 switch - L3 routing between two separate networks? | NETGEAR Communities

Hi,There are two different entities that however trust each other to a certain degree.Each entity has it's own LAN and switches and gateway and internet...

Connecting EVO Servers to XS712T Switch | NETGEAR Communities

Trying to set up the XS712T with two EVO servers going into a 10Gbs Ethernet port on MacBook Pro.  I can access the Netgear web management (the switch...

inefficient Setup Layer 2+3 LAG with XS712Tv2 and Qnap NAS | NETGEAR Communities

Hi togetherwanted to have better speeds when many users accessing files on a qnap NAS ( TVS-872XT + QXG-10G2T-107 ).So I activated Link...

Unreliable cold boot XS712T | NETGEAR Communities

I bought a used XS712T for about 200euro, and I have problems booting it up from cold.The pattern I describe below has made itself apperant over many days of...

XS712Tv2 can not send a jumbo frame via LAG connection | NETGEAR Communities

Hello!!I am testing a jumbo frame from a Linux PC to another Linux PC via XS712Tv2.$ ping -M do -s 1474 -c 10 $destinationpc        ...

Switch xs712t v2 and Intel x710 | NETGEAR Communities

Hello,can I connect a Intel x710-da2 card in my switch Netgear XS712T-V2?

Can a 5 GbE network expansion card be used with a 10 Gigabit XS712Tv2? | NETGEAR Communities

Hi, I would like to connect a QNA-UC5G1T 5 GBE card in a TS-873 to a 10 Gigabit Netgear XS712Tv2 switch. However, I am afraid that the XS712Tv2 does not...

ProSafe XS712T power on Doesnot boot | NETGEAR Communities

Hi Community,NETGEAR 12-Port 10G Ethernet Smart Switch (XS712T) turns on although no activity on power and fan LED. Both fans are working as well. There is...

Two XS712Tv2 switches need configuration for contineous connectivity if any one fails | NETGEAR Communities

We want an on site engineer to install and configure the managed swithes with port stacking.

How to unbrick a XS712T ? | NETGEAR Communities

It seems that I bricked (?) our reserve XS712T. Fan is running high but no LED is blinking or even lighting up.All totally dark, while the fan thinks it is a...

Netgear XS712T v2 socket xg12 "detach" | NETGEAR Communities

I hope someone on this discussion board can help. I have a Netgear Prosafe XS712T v2 network switch that supports a mixture of 10Gb/s devices connected...

Netgear Prosafe XS712T stock fan replacement? | NETGEAR Communities

I have setup a 10GbE home network/lab, and my backbone is the XS712T. Not the version 2, but the older model. Its used and possibly out of warranty. The...

Networking solution ensures Hawk-Eye Innovations never misses the mark - NETGEAR Blog

Discover how NETGEAR networking powers Hawk-Eye’s real-time precision and reliability across global sporting events.